Lubrication System

• Set for testing engine oil pressure

• Provided with 11 oil pressure switch adapters for the most comprehensive car application coverage on the market, including
- R 1/8” DIN adapter
- 1/8” x 27 NPT adapter
- 1/4” x 18 NPT adapter
- 3/8” x 18 NPT adapter
- M10 × P1.0 adapter
- M10 × P1.25 adapter
- M12 × P1.5 adapter
- M12 x P1.75 adapter
- M14 × P1.5 adapter
- M16 × P1.5 adapter
- M16 x P2.0 adapter

• Also including two oil filter adapters for Mercedes-Benz M271 and M274 when oil pressure switch is very hard to access to

• 1.5 meter long manometer hose makes it easier to connect to oil pressure switches in tight spaces

• Please check the Application tab below for reference. The list is partial - please contact us for more information

• 74.3 mm × 14 flutes × 45 mm (height)

• 3/8" drive

• For Mercedes-Benz

• Material: hot rolled steel

• Heavy duty construction tool for removing oil filter canisters on Iveco trucks and van

• 107.3 mm x 15 flutes

• 1/2" square drive to allow sufficient torque required to remove large size oil filter canisters

• Use a manual wrench with this fuel filter wrench. DO NOT use an air/impact wrench

• Heavy duty construction tool for removing oil filter housings on MAN trucks and buses

• 135.7 mm x 18 flutes

• 1/2" square drive to allow sufficient torque required to remove large size oil filter housings

• Use a manual wrench with this fuel filter wrench. DO NOT use an air/impact wrench

• Heavy duty construction tool for removing oil filter housings on Scania trucks

• 78.1 mm x 6 points

• 1/2" square drive to allow sufficient torque required to remove large size oil filter housings

• Use a manual wrench with this fuel filter wrench. DO NOT use an air/impact wrench

• Set for testing engine oil pressure

• Provided with 11 oil pressure switch adapters for the most comprehensive car application coverage on the market, including
- R 1/8” DIN adapter
- 1/8” x 27 NPT adapter
- 1/4” x 18 NPT adapter
- 3/8” x 18 NPT adapter
- M10 × P1.0 adapter
- M10 × P1.25 adapter
- M12 × P1.5 adapter
- M12 x P1.75 adapter
- M14 × P1.5 adapter
- M16 × P1.5 adapter
- M16 x P2.0 adapter

• Long manometer hose (1.5 meter) makes it easier to connect to oil pressure switch located in hard to access locations

• Please check the Application tab below for reference. The list is partial - please contact us for more information

• Clamping device for connecting engine oil filter canisters by piercing through the surface for
oil pressure tests

• Especially helpful when oil pressure switch is situated at a hard-to-reach location

• Suitable for oil filter canisters with diameters between 75 and 125 mm / 2.95 and 4.92 inches

• Not suitable to work on cartridge style nylon oil filter housings

• Nylon oil drain plug used on Buick, Cadillac, Chevrolet, GMC, and Opel models

• Drain plug should be changed each time after oil change

• Compatible with OE number 12713651

• Nylon oil drain plug used on Ford models

• Drain plug should be changed each time after oil change

• Compatible with OE number KX6Z-6730-B

• Nylon oil drain plug used on Ford models

• Drain plug should be changed each time after oil change

• Compatible with OE number FT4Z-6730-A

• Kit for repairing damaged, stripped, or worn drain plug hole by enlarging the threads with taps provided and new (and bigger) drain plugs with copper washers

• Suitable for cars with M12 × P1.75 drain plugs

• Applicable for GM (Buick, Cadillac, Chevrolet, GMC) and Ford (Ford, Jaguar, Mazda)

• Oil filter removal tool for use on Hyundai and Kia 2.0L and 2.2L CRDI engines

• For Hyundai ix35, Santa Fe, Tucson
• For Kia Carnival, Sorento, Sportage

• Size 42 mm x 3/8" square drive