Engine Services

• Precise test for engine block and cylinder head when reassembling or overhauling an engine

• Work with a feeler gauge

• Suitable for 4- and 6-cylinder engines

• Tolerance < 0.05 mm

• Tool for removing fuel pump locking rings for various car makes and models, for gasoline and diesel engines

• Compatible with BMW, Hyundai, Kia, and Mercedes-Benz, and more

• See more details in the Applications section.

• Heavy duty design with 1/2” square drive to provide sufficient torque when removing stubborn fuel pump lock rings

• Fuel filter removal tool for use on Mitsubishi Triton 2.5 diesel engines

• Two pieces in a set, the big tool for holding the filter housing, and the small tool for holding the fuel filter sensor

• Big tool size 97.7 mm x 15 flutes x 1/2" square drive
• Small tool size 44.8 mm x 12 sides

• 2 pieces wrench set for removing diesel fuel filter housings while protecting the sensors

• Fitting Ford, Mazda, Mitsubishi, Nissan, and Toyota diesel engines. Please check the Application tab below for reference

• 1/2” square drive to provide extra torque when encountering stubborn fuel filters

• Filter wrench size 86 mm x 15 flutes x 1/2" square drive
• Sensor wrench size 50.3 mm x 8 sides

• Fuel filter removal tool for use on Hyundai and Kia diesel engines

• For Hyundai Accent, Elantra, H-1, ix35, Trajet, Tucson, and more
• For Kia Ceed, Cerato, Picanto, Sedona, Soul, Sportage, and more

• Size 71 mm x 14 flutes x 1/2" square drive

• Application below shows partial fitment. For more information, please contact us directly

• Fuel filter removal tool for use on Hyundai and Kia 2.2 CRDI engines

• For Hyundai Palisade and Santa Fe
• For Kia Carnival and Sorento

• Size 108 mm x 15 flutes x 1/2" square drive

• Fuel filter removal tool for use on Hyundai and Kia 1.6L CRDI engines

• For Hyundai i30, i40, Kona, Tucson
• For Kia Ceed, Optima, Sportage, Stonic

• Size 80.7 mm x 14 flutes x 1/2" square drive

• Application below shows partial fitment. For more information, please contact us directly

• Diesel fuel filter removal tool for use on LDV Maxus V80, V90, G10, and G20

• High quality made tool with grooves fit perfectly the small tabs on the outer rim of the fuel filter

• Large and long handle to create sufficient torque while removing

• Ø121mm with 15 grooves, total length of 290 mm

• Tool precisely-made with slots to mesh with the ribs on fuel filter on Ford Transit and Tourneo 2.2 TDCi engines

• Helps safely remove and leak-free install the fuel filter

• 3/8" square drive

• OEM number 207 1140 001 00

• Use a manual wrench with this fuel filter wrench. DO NOT use an air/impact wrench

• Highly versatile tool kit, provided with a 5 lb slide hammer, for a variety of pulling operations on car

• Including a front hub puller and rear axle puller for most CV axle removal and gear hub bearing replacement

• Including dent puller, and other parts for pulling press-fit parts, such as bushings, bearings, gears, and seals ... etc

• Jaws can be assembled into 2-way and 3-way yokes for pulling either internal or external bearings

• Forged carbon steel used as the primary material that provides high strength and corrosion proof, and is resistant to severe sliding applications

• Tool precisely-made with slots to mesh with the ribs on fuel pump locking rings for Toyota and Lexus

• Elevated bridge to avoid blockage from connectors and lines on fuel pump

• Helps remove and install the fuel pump locking rings easier and faster

• 3/8" square drive - 19 mm hex

• OD 177 mm / 7 inch - ID 143 mm / 5.6 inch

• Set for pulling blind hole bearings off in an energy saving way

• Includes a slide hammer and a puller

• Provided with adapters that can be expanded within the blind hole for stronger connection